Screws

A fully threaded, grade 8.8 high tensile set screw used in a wide variety of applications. NOTE: Nuts not included. • Plated in Trivalent Chromium (Cr3) Zinc • Manufactured from grade 8.8 carbon steel

Type P hexagonal nylon nut with a metric thread. Also known as locking nuts, designed to prevent the nut from loosening. Used for all bolting and fastening applications.

Type P hexagonal nylon nut with a metric thread. Also known as locking nuts, designed to prevent the nut from loosening. Used for all bolting and fastening applications.

Type P hexagonal nylon nut with a metric thread. Also known as locking nuts, designed to prevent the nut from loosening. Used for all bolting and fastening applications.

Tension-free, structural screw anchor suitable for heavy loads and small centre-to-centre distances and edge distances. For concrete, sand-lime brick and masonry. ETA approved for structural permanent attachments in both the tension and compression zones of concrete. Integrated pressed-on flange with locking profile under the head. Dimensions listed on top of anchor for possible inspection. Beautiful finish on visible work.

Commonly used with drop in anchors for suspending cable trays from ceilings or can be cut to a required length and used with chemical resin.

A versatile, torque controlled through fixing for use in a wide range of anchoring applications into concrete. Complete with hex full nut and washer. NOTE: If no torque wrench is available, tighten the nut 3 to 4 full turns from finger tight.

Used to secure plasterboard to drywall and ceiling track systems with a max. of 0.6mm thickness.

Hex head self-drilling screws, for joining roofing sheets to light section steel (Max. 5.0mm) without the need to pre-drill a hole. • Fire Classification - A1

Designed as an alternative to the traditional coach screw mainly used for timber to timber applications. Wafer head for improved clamping and a low profile finish. Coated with a patented multi-layer corrosion resistant plating to withstand 1,000 hours salt spray test, this screw is ideal for external applications.

Galvanized through anchors / clickers for fast, reliable, approved, heavy-duty fixings in cracked and non-cracked concrete. With stainless steel expansion clip so that the part of the anchor where the load capacity is built up is not subject to corrosion. Placement depth marking on each anchor prevents incorrect installation. ETA approved for structural permanent attachments in both the tension and compression zones of concrete.

Using the most modern manufacturing methods and design techniques, the C2 is a revolutionary high performance multi-purpose screw. Designed to give ultimate performance in a multitude of materials

Used when constructing drywall track and ceiling track systems to stitch the track together (Max. 3.0mm) without the need to pre-drill a hole. • Fire Classification - A1

Used to secure plasterboard to drywall and ceiling track systems with a max. of 0.6mm thickness.

Designed as an alternative to the traditional coach screw mainly used for timber to timber applications. Coated with a patented multi-layer corrosion resistant plating to withstand 1,000 hours salt spray test, this screw is ideal for external applications.

A versatile heavy duty coach screw with a hex flange head and is the modern replacement for traditional DIN 571 coach screws. Benefits from an aggressive slash point tip for easy driving and reduced splitting. Suitable for softwood, hardwood, man-made board or masonry with the use of a nylon plug. Zinc plated and yellow passivated for improved corrosion resistance.

Galvanized through anchors / clickers for fast, reliable, approved, heavy-duty fixings in cracked and non-cracked concrete. With stainless steel expansion clip so that the part of the anchor where the load capacity is built up is not subject to corrosion. Placement depth marking on each anchor prevents incorrect installation. ETA approved for structural permanent attachments in both the tension and compression zones of concrete.

All the features and superior performance of the Classic Multi-Purpose Screw manufactured from A2 Stainless Steel. Ideal where ultimate corrosion resistance is required when fixing to softwoods, hardwood (pre-drilled), chipboard, MDF and plastic. Stainless steel must be used where there is corrosive environment and/or the base material has inherent corrosive characteristics e.g. Green Oak.

Used to secure plasterboard to drywall and ceiling track systems with a max. of 0.6mm thickness.

Designed as an alternative to the traditional coach screw mainly used for timber to timber applications. Coated with a patented multi-layer corrosion resistant plating to withstand 1,000 hours salt spray test, this screw is ideal for external applications.